Please use this identifier to cite or link to this item: https://hdl.handle.net/20.500.11851/11646
Title: The Atlas Experiment at the Cern Large Hadron Collider: a Description of the Detector Configuration for Run 3
Authors: Amerl, M.
Filmer, E.K.
Jackson, P.
Kong, A.X.Y.
Potti, H.
Ruggeri, T.A.
Ting, E.X.L.
Keywords: Calorimeter methods
Large detector systems for particle and astroparticle physics
Muon spectrometers
Particle tracking detectors
Colliding beam accelerators
Data acquisition
Electron energy levels
Energy dissipation
Hadrons
Heavy ions
Liquefied gases
Luminance
Particle detectors
Wheels
Astroparticle physics
ATLAS detectors
Calorimeter method
Detector systems
Large detector system for particle and astroparticle physic
Large detectors
Muon spectrometer
Particle tracking
Particle tracking detector
Tracking detectors
Calorimeters
Publisher: Institute of Physics
Abstract: The ATLAS detector is installed in its experimental cavern at Point 1 of the CERN Large Hadron Collider. During Run 2 of the LHC, a luminosity of ℒ = 2 × 1034 cm-2 s-1 was routinely achieved at the start of fills, twice the design luminosity. For Run 3, accelerator improvements, notably luminosity levelling, allow sustained running at an instantaneous luminosity of ℒ = 2 × 1034 cm-2 s-1, with an average of up to 60 interactions per bunch crossing. The ATLAS detector has been upgraded to recover Run 1 single-lepton trigger thresholds while operating comfortably under Run 3 sustained pileup conditions. A fourth pixel layer 3.3 cm from the beam axis was added before Run 2 to improve vertex reconstruction and b-tagging performance. New Liquid Argon Calorimeter digital trigger electronics, with corresponding upgrades to the Trigger and Data Acquisition system, take advantage of a factor of 10 finer granularity to improve triggering on electrons, photons, taus, and hadronic signatures through increased pileup rejection. The inner muon endcap wheels were replaced by New Small Wheels with Micromegas and small-strip Thin Gap Chamber detectors, providing both precision tracking and Level-1 Muon trigger functionality. Trigger coverage of the inner barrel muon layer near one endcap region was augmented with modules integrating new thin-gap resistive plate chambers and smaller-diameter drift-tube chambers. Tile Calorimeter scintillation counters were added to improve electron energy resolution and background rejection. Upgrades to Minimum Bias Trigger Scintillators and Forward Detectors improve luminosity monitoring and enable total proton-proton cross section, diffractive physics, and heavy ion measurements. These upgrades are all compatible with operation in the much harsher environment anticipated after the High-Luminosity upgrade of the LHC and are the first steps towards preparing ATLAS for the High-Luminosity upgrade of the LHC. This paper describes the Run 3 configuration of the ATLAS detector. © 2024 CERN for the benefit of the ATLAS collaboration.
URI: https://doi.org/10.1088/1748-0221/19/05/P05063
https://hdl.handle.net/20.500.11851/11646
ISSN: 1748-0221
Appears in Collections:Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection

Show full item record



CORE Recommender

SCOPUSTM   
Citations

2
checked on Dec 21, 2024

WEB OF SCIENCETM
Citations

1
checked on Dec 21, 2024

Page view(s)

62
checked on Dec 16, 2024

Google ScholarTM

Check




Altmetric


Items in GCRIS Repository are protected by copyright, with all rights reserved, unless otherwise indicated.